There is no fixed price list for steel beams at TL Steelworks: every beam is quoted on its size, length, connections, finish, calculations and delivery or installation. Send us your engineer’s drawings or project details and we will price the beam you actually need.
By the TL Steelworks Technical Team, working from our 15,000 sq ft facility in Verwood, Dorset.
Most people searching for steel beam prices want a figure before they ring round. We understand that. The honest answer is that two beams for two extensions can differ a great deal, because the steel is only part of the cost. Below we set out what goes into the price of a beam and what you can send us with your enquiry.
How are steel beams priced?
Every steel fabrication project is priced around its specific design, materials, engineering and installation requirements. We do not publish a price list, because a single RSJ (rolled steel joist) for a kitchen wall and a goal post frame (a beam carried on two steel columns) for a rear extension share little except the material.
A tailored quote covers the parts that apply to your job. That can be design and calculations, the steel itself, fabrication, painting, delivery and installation. If you only need the beam, we price supply only. If you want one team to handle the lot, we price supply and fit.
What affects the price of a steel beam?
Every quote is based on design complexity, steel type and quantity, fabrication requirements, engineering and calculations, site surveys, protective finishes, and delivery and installation. The table shows how each one applies to a beam.
| Price factor | Why it changes the cost |
|---|---|
| Section size and weight | The engineer sizes the beam for its span and load. A deeper, heavier section uses more steel. |
| Length and quantity | One beam for a single opening costs less than several members for a whole floor or extension. |
| Beam type | Universal Beams (UB), Universal Columns (UC), lintel support beams and goal post frames each need different work. |
| Fabrication | Bearing plates, end plates, holes for bolts and connection details all add workshop time. |
| Design and calculations | If you have no structural engineer yet, our in-house engineer can produce the design and calculations. |
| Protective finish | Coating is chosen for where the beam will sit, inside a dry house or exposed near the coast. |
| Delivery and installation | Access, lifting method and how the work fits your build programme. |
Is an RSJ the same price as a steel beam?
Yes, because an RSJ is a steel beam. RSJ is the term most builders and homeowners still use. Modern projects are usually designed with Universal Beams (UB) or Universal Columns (UC), chosen by a structural engineer for the loads in your building.
So when you ask us for an RSJ price, we price the section your engineer has specified, with the fabrication and finish it needs. The name on the quote matters far less than the size, length and connections on the drawing. If you have a drawing that says UB with a size reference, send it as it is. If you only have a builder’s note that says RSJ, send that too and we will talk it through with you. You can read how we fit them on our RSJ installation page.
Do I need structural calculations before I can get a price?
You need them before the beam is made, and having them makes the quote accurate. A qualified structural engineer must specify the beam size and provide calculations before fabrication begins. Building Control will also want to see them for most structural alterations, such as removing a load-bearing wall.
If you already have an engineer, we work from their calculations and approved drawings. If you do not, our in-house engineer can produce the structural design and calculations to support your Building Control application. We consider this before fabrication, never after the steel is cut. That is where most of the money is saved: the most expensive mistakes on a steel job happen before the first piece of steel is cut, when a beam is made from a guess and does not fit.
Supply only or supply and fit: which costs less?
Supply only costs less up front, and it suits builders who have their own lifting kit and labour. Supply and fit costs more on the quote but puts the whole job with one team, from measurement to installation.
With supply only, you collect the beam or we deliver it. Same-day or next-day collection from our Verwood facility is available for some structural steelwork. Your builder then handles temporary support (props and needles that hold the wall while it is opened up) and lifting.
With supply and fit, we survey, fabricate, paint, deliver and install. We use a spider crane (a compact tracked crane that fits through narrow access) for safe lifting where access allows. The beam is set on its bearings and secured to the approved design. The installation itself is often done within a day, depending on beam size, access and how complex the job is.
How does the finish change the cost of a steel beam?
The finish adds to the price, and it is chosen for where the beam lives rather than how it looks. A beam boxed in behind plasterboard in a dry house needs a different coating to steel exposed to weather or sea air.
We paint and finish in our own purpose-built painting facilities, as part of controlling the quality of the job. That also saves the time and handling of sending the steel to another firm. Coastal properties across Dorset and Hampshire need more thought here, because salt air works on poorly protected steel. If your beam will be outside, in a garage, or near the coast, tell us at the first enquiry. Our guide on which steel and finish to use for outdoor and coastal steel explains the choices.
What is included in a TL Steelworks steel beam quote?
A quote covers each stage that applies to your project. This is our typical process, framed as how we usually run a beam job rather than a promise for every site.
First, you call or send drawings, dimensions and details. We then set the brief: what the beam must carry, where it goes and the finish. Where needed, we survey the site with total stations (precise electronic measuring instruments) alongside traditional measurement, recording the real openings, bearings and levels.
Next, we produce fabrication drawings in Tekla Structures and Advance Steel, and you approve them before manufacture. Calculations come from your engineer or ours. The beam is then made and painted in our Verwood workshops. Finally, we deliver to suit your programme, with staggered deliveries where the build needs them, and install if that is part of the job.
How can I get an accurate steel beam price quickly?
Send the structural engineer’s calculations or drawings with your first enquiry. That one document answers most of what we need to price the beam.
If you do not have calculations yet, send the width of the opening, photos of the wall and the rooms either side, and what sits above it. Tell us whether there is an upper floor, a roof or a chimney breast overhead. Say where the property is and how easy access is for delivery. Let us know whether you want supply only or supply and fit, and when your builder needs the steel on site. With that, we can tell you what the job needs and quote it properly, rather than guess.
Steel beam price questions
Do you publish a price list for steel beams?
No. Every beam is quoted on its design, steel, fabrication, finish, engineering and installation, so a list price would be wrong for most jobs.
Will you quote for just one beam?
Yes. We handle everything from a single beam for a home renovation to multiple structural members for industrial-scale developments.
Can I collect the beam myself?
Yes, for some structural steelwork. Same-day or next-day collection from our Verwood facility is available, depending on the beam and what fabrication it needs.
Can you work from my engineer’s drawings?
Yes. We fabricate directly from approved structural drawings and engineering calculations, and we can produce them in-house if you have none.
Which areas do you deliver to?
We work across Dorset, Hampshire and the wider south of England from our workshop in Verwood. See the towns and areas we cover.
Get a tailored steel beam quote
Share your drawings or project details to receive a tailored quotation. Call 01202 285449 or 07938 826490, email tlsteels@outlook.com, or send your drawings through our contact page. You can also read more about our steel beam supply and installation.
The team at TL Steelworks



